|
Feature Summary CC2-TANGO
|
|
Form Factor
|
CompactPCI Single size CompactPCI style Eurocard (160x100mm2),
front panel width 4HP (20.3mm)
|
|
Processor
|
Designed for Intel® ULV Celeron® and
LV Pentium® III Micro FC-BGA processors (Tualatin 0.13µ generation),
maximum junction temperature 100°C
• CC2-1: 400MHz ULV Celeron, 0.95V, 100MHz FSB, 256KB L2 cache, 3.4W typical
• CC2-2: 650MHz ULV Celeron, 1.10V, 100MHz FSB, 256KB L2 cache, 7.0W typical
• CC2-3: 800MHz LV Pentium 3, 1.15V, 133MHz FSB, 512KB L2 cache, 11.2W typical
• CC2-4: 933MHz LV Pentium 3, 1.15V, 133MHz FSB, 512KB L2 cache, 12.2W typical
|
|
Chipset
|
Intel i815G chip set consisting of:
• 82815 Graphics/Memory Controller Hub (GMCH)
• 82801 I/O Controller Hub (ICH2)
• 82802 Firmware Hub (FWH)
|
|
Memory
|
•144-pin SO-DIMM socket
•Support for up to 512MB, PC133, non ECC, unbuffered SDRAM
•Support for serial presence detect (SPD) and non-SPD SO-DIMMs
|
|
Video I/O
|
Analog monitor and digital flat-panel display support by DVI-I connector (front panel),
up to 1280x1024 pixel 16M colors 85Hz refresh rate, incorporates PanelLink Digital
technology (Silicon Image). Option: D-SUB (female HD15) connector available,
replaces DVI-I connector
|
|
USB I/O
|
Ports over-current protected, data transfer rate of up to 12Mbps, conforming to USB1.1
• USB port 1: Type A connector (front panel)
• USB port 2: J2/P2 Rear I/O option
|
|
Ethernet I/O
|
10/100Mbps Fast Ethernet controller, 82551ER chip, RJ45
|
|
Legacy I/O
|
• LPC Super-I/O interface connector, CC6-ACID/CC0-CHILLOUT companion boards available
• J2/P2 Rear I/O option: Keyboard, Mouse, COM1 (TTL only)
|
|
IDE/ATA
|
• Ultra ATA/100 40-pin connector (primary IDE)
• CompactFlash socket for CFA ATA cards (secondary IDE)
• J2/P2 Rear I/O option: Primary IDE
|
|
CompactPCI
|
32-bit, 33.3MHz, PCI bridge chip Texas Instruments PCI2050, 133MBps CPCI master
|
|
J2/P2 Rear I/O Option
|
• Primary IDE
• USB Port 2
• Keyboard, Mouse
• COM1 (TTL Level)
|
|
PXI Support
|
TRIG0, TRIG1, TRIG6, TRIG7 (can be alternatively used as GPIO)
|
|
BIOS
|
Phoenix BIOS, single or dual FWH (8/16Mbit Flash Memory)
|
|
Power Requirements
|
- CC2-1-TANGO: +5V±0.25V 1.3A max.+3.3V±0.1V 1.1A max.
- CC2-2-TANGO: +5V±0.25V 1.9A max.+3.3V±0.1V 1.3A max.
|
|
Thermal Conditions
|
Standard processor heatsink according to Intel spec. option 2, 9.8K/W (natural convection),
3.95K/W (forced airflow @ 200LFM), or similar heatsink. Custom specific cooling solutions on request.
• CC2-1: 0-40°C (natural convection cooling), 0-70°C * (200LFM forced airflow)
• CC2-2: 0-60°C (200LFM forced airflow), 0-70°C (400LFM forced airflow)
• CC2-3: 0-45°C (200LFM forced airflow), 0-65°C (400LFM forced airflow)
• CC2-4 0-40°C (200LFM forced airflow), 0-65°C (400LFM forced airflow)
* Limited to 70°C due to other components than the processor
Storage temperature -40°C to +85°C
Humidity 5-90% non condensing
|
|
MTBF
|
0.113 * 106h
|
|
Altitude
|
-300m to +3000m
|
|
Shock
|
15g 0.33ms, 6g 6ms
|
|
Vibration
|
1g 5-2000Hz
|
|
Typical Calculating Performance
|
PCMark2002 under Windows 2000, CPU/MEM Score
- 1274/886 @400MHz
- 1990/933 @650MHz
- tbd @800MHz
- 2854/1467 @933MHz
|
Subject to change
CC2-TANGO - Component Assembly (Top View)
|
CC2-TANGO - Block Diagram
|
CC2-TANGO with DVI-I Video
|
Available as a companion board to the CC2-TANGO, the
CC6-ACID is provided with several
legacy I/O ports. This module can be mounted either to the bottom side or on
top of the CC2-TANGO and communicates across the LPC (Low Pin Count) interface.
The CC6-ACID will be required only if the classical interfaces, e.g. serial
and parallel port, remain in use in a given application.
|
|
As an option, the CC6-ACID can be delivered with an on-board 2.5-" hard
disk drive, resulting in a very compact system. The connectors COM1/2, LPT,
mouse and keyboard are situated at the front panel (4HP and 8HP versions
available), while an external floppy disk drive can be attached via the on-board
pin header.
The CC0-CHILLOUT is similar to the CC6-ACID, but destined for use together
with a rear I/O transition module (CCZ-RIO).
|
CC6-ACID - Block Diagram
|
CC0-CHILLOUT - Block Diagram
|
Available as an option, the CC2-TANGO can be delivered for rear I/O utilization.
Several I/O ports can be routed across the J2 connector. Rear I/O requires that
a suitable J2 backplane is present in your CompactPCI system. By default, the
CC2-TANGO is equipped with line terminating resistors for a common 64-bit CPCI
J2 backplane.
|
|
The CCY-RIO transition module provides a 4HP back panel with connectors for PS/2
style keyboard and mouse, a serial RS-232E COM port, and an USB receptacle.
In addition, optional on-board headers are stuffed on the CCY-RIO for attachment
of IDE/ATA devices (hard disks, DVD ROM drives).
|
CCY-RIO - Assembly Drawing
|
|
Ordering Information
|
|
Alias
|
Ordering No.
|
Short Description
|
|
TANGO
|
CC2-1-TANGO
|
3U/4HP CPCI CPU Board, ULV Celeron 400MHz µFCBGA 0.13µ processor,
256MB SDRAM, 256KB cache, 100MHz FSB, 100Mbps Ethernet
|
|
TANGO
|
CC2-2-TANGO
|
3U/4HP CPCI CPU Board, ULV Celeron 650MHz µFCBGA 0.13µ processor,
256MB SDRAM, 256KB cache, 100MHz FSB, 100Mbps Ethernet
|
|
TANGO
|
CC2-3-TANGO
|
3U/4HP CPCI CPU Board, LV Pentium III 800MHz µFCBGA 0.13µ processor,
256MB SDRAM, 512kB cache, 133MHz FSB
|
|
TANGO
|
CC2-4-TANGO
|
3U/4HP CPCI CPU Board, Pentium III 933MHz µFCBGA 0.13µ processor,
256MB SDRAM, 512kB cache, 133MHz FSB
|
|
|
CC2-8-TANGO
|
512MB SDRAM Option
|
|
ACID
|
CC6-1-ACID
|
3U CompactPCI Super-I/O module, local expansion board complementing the
CC2-TANGO, front panel width 8HP, mounting on top of the CC2-TANGO
|
|
ACID
|
CC6-3-ACID
|
Similar to the CC6-1-ACID, front panel width 4HP, w/o parallel port,
mouse/keyboard combined in one Mini-DIN connector (external splitter
cable available as accessory), mounting on the top or
bottom side of the CC2-TANGO
|
|
|
CC6-8-HDK
|
Optional hard disk drive, on-board mounting on top of the CC6-1 and CC6-3
|
|
CHILLOUT
|
CC0-1-CHILLOUT
|
3U Super-I/O module, local expansion board complementing the CC2-TANGO,
front panel 4HP, intended for rear I/O (rear I/O transition module CCZ-RIO
required), mounting on top or bottom of the CC2-TANGO
|
|
RIO
|
CCY-1-RIO
|
Rear I/O transition module for CC2-TANGO
|
|
RIO
|
CCZ-0-RIO
|
Rear I/O transition module for CC0-CHILLOUT
|
|
|
CR9-5-ADAPT
|
Mechanical kit, expands the CC2 front panel to 6U full height
|
|
|
280.7.400
|
external keyboard/mouse Y-splitter-cable Mini-DIN male to 2 x Mini-DIN female
(required for CC6-3 only)
|
|
|
908.51.02.01
|
DVI-D to DVI-D cable assembly, 2m, connects the CC2-TANGO to DVI monitors
(digital way)
|
|
|
908.57.02.01
|
DVI-I to HD DSUB15 cable assembly, 2m, connects the CC2-TANGO to VGA monitors
(analog way)
|
|
|
908.57.12.01
|
DVI-I to VGA adapter (plug to receptacle), to be plugged onto the CC2-TANGO DVI
output, with HD DSUB15 socket, suitable especially for analog monitors with
attached VGA cable
|
|
